Conference Session: Energy efficiency and energy management within industry and building
Utilisation of energy in process and other industrial enterprises; Energy efficiency and sustainable development of process and other industrial enterprises; Energy-efficient technologies; Improving of process management and automation; Problems and possibilities of co-generation and tri- generation usage; The use of waste heat; Revitalization of technological energy systems in industrial companies; Energy Management Programs; The situation analysis and optimization methods in industrial energy; Measurement, control and process visualization
Papers selected for Conference Session titled : Energy efficiency and energy management within industry and building
back to the Sessions
Branislav Gajić (Mašinski fakultet Univerziteta u Beogradu)
Abstract
In today’s industry a lot of products are being made from viscous, non-Newtonian fluids. Main examples of non-Newtonian fluid that are being used or made in industry are: chocolate and it’s products, mayonnaise, ketchup, different types of oils, molten polymers, etc. As an example in this paper properties of chocolate are given and a few configurations of pipeline for chocolate distribution. Pressure drop due to local resistance and fluid friction has been calculated and conclusions on effect of differences in pipeline configuration is given. The pipeline configuration directly affects on pump selection, especially for pumps that distributes non-Newtonian fluids. Also, effect on energy consumption is given in tables.
Milan Bulajić, prof. dr Jelena Svorcan (Univerzitet u Beogradu - Mašinski fakultet)
Abstract
Over the past decade, vertical take-off and landing unmanned aerial vehicles have gained increasing importance in both military and civilian applications. This development has intensified research into UAV propulsion systems, particularly propeller design. Modern propellers are required to provide high aerodynamic efficiency while maintaining low noise emissions, due to acoustic detectability in military applications and noise pollution in civilian environments. Since propeller efficiency directly affects flight endurance, payload capacity, and energy consumption, continuous efforts are being made to improve its aerodynamic performance.
This paper investigates the aerodynamic performance and power requirements of a 10-inch UAV propeller through a comparison of analytical and numerical prediction methods. Analytical models offer rapid performance estimation with low computational requirements, making them suitable for preliminary design and optimization. However, their accuracy may be limited by simplifying assumptions regarding blade geometry and flow behavior.
Computational fluid dynamics provides a more detailed representation of the three-dimensional flow field around the propeller blades, although at a higher computational cost. The two approaches are compared based on predicted thrust, torque, power consumption, and propeller efficiency under selected operating conditions. Their advantages, limitations, and suitability for different stages of UAV propeller development are also discussed.
Goran Jankes (Univerzitet u Beogradu, Mašinski fakultet)
Nikola Tanasić (Akademija strukovnih studija Politehnika)
Abstract
Korišćenje energije za pokriće bilo koje od ljudskih potreba ili aktivnosti (procesi grejanja ili hlađenja prostorija, proizvodni procesi, proizvodnja energije, saobraćaj), odvija se na taj način da se energija od primarne, ili ulazne energije, transformiše više puta do korisne energije.
Korisna energija je energija koja se neposredno koristi za sam proces, bilo da je to koristan rad, toplota potrebna za preradu sirovine u gotov proizvod, ili toplota potrebna za održavanje željene temperature u nekom prostoru.
Svaka od ovih transformacija neizbežno se odvija uz gubitak dela ulazne energije u okolinu. Energija koja se gubi u okolinu u procesu transformacije energije naziva se otpadna toplota. Otpadna toplota je nužan proizvod mašina koje proizvode rad i svih drugih procesa koji koriste energiju. Potreba da neki sistem otpušta deo toplote kao nusprodukt transformacije energije leži u osnovnim zakonima termodinamike.
Otpadna toplota je najveći i neiskorišćeni izvor energije na svetu. Generiše se u industrijskoj proizvodnji, hlađenju kompjuterskih data centara, u postrojenjima za otpadne vode, od zagrevanja stanica metroa i sa drugih mesta. Ta toplota bi se usmeravanjem kroz sistem daljinskog grejanja lako mogla upotrebiti za zagrevanje domaćinstava, ili za pokriće potreba za toplotnom energijom u industriji. Procena je da se u EU ispušta 2,86 petavat-sati otpadne toplotne energije godišnje. To odgovara ukupnoj potražnji u EU za grejanje u stambenim zgradama i zgradama u sektoru usluga poput škola, bolnica, hotela, restorana, kancelarija i tržnih centara.
Uobičajeni izvori otpadne toplote u industriji su: Industrijski kotlovi, Industrijske peći, Sistemi za hlađenje, Tehnološka voda i Otpadni gasovi iz industrijskih procesa, Otpadni vazduh iz ventilacije hala i sušara, Hlađenje industrijske opreme.
U radu se za ove sisteme definišu karakter i količine otpadne toplote.
Otpadna toplota se ne može izbeći, ali je imperativ da se koristi na adekvatan način.
Ponovna upotreba otpadne toplote daje značajne efekte: povećanje energetske efikasnosti, smanjenje emisije CO2 i smanjenje troškova za energiju. Najprikladnije opcije za ponovnu upotrebu otpadne toplote u svakom konkretnom slučaju zavise od više faktora, pre svega od vrste industrijskih procesa, temperature i količine proizvedene otpadne toplote, okolne infrastrukture i potrošača toplotne energije gde se može koristiti otpadna toplota. U radu su prikazani karakteristični primeri korišćenja otpadne toplote.
Neophodno je da se otpadna toplota nekog procesa u industriji shvati kao energetski resurs, a ne kao nužni gubitak energije.
Potencijali za korišćenje otpadne toplote određuju se energetskim auditom.
Saša D. Stašević (Student doktroskih studija Mašinski fakultet Univerziteta u Beogradu)
Abstract
Three-pass fire-tube boilers are widely used for industrial steam and hot water generation, yet the simplified models assume a constant overall heat transfer coefficient and geometrically uniform tube passes. Such assumptions can introduce significant error, since the fire tube and the convective tube bundles differ substantially in diameter, surface area, and dominant heat transfer mechanism, while the local heat transfer coefficient itself varies along the flow path as the flue gas cools. This paper presents a mathematical model that accounts for both effects and considers assumptions that address the inequality of heat transfer coefficients and geometrical uniformity. The first pass, a single large-diameter fire tube, is modelled with a position-dependent overall heat transfer coefficient combining convective and radiative exchange over the initial two-thirds of its length. After the initial two-thirds of the length, the radiation exchange is considered to be substantially lower. The second and third passes, consisting of tube bundles of smaller diameter, are modelled with convective heat transfer, but the heat transfer coefficients are still dependent on the flow direction. The governing equations form a system of coupled, nonlinear ordinary differential equations along the shared axial coordinate of the three passes, with the radiative term introducing explicit temperature dependence. The system is solved numerically as a boundary value problem, with matching conditions at the two return chambers connecting the passes. The resulting temperature profiles characterize the relative contribution of radiation to total heat duty in the fire tube and quantify the deviation from a uniform-coefficient approximation.
Luka Božić, Balša Ćeranić, Leposava Ristić (Elektrotehnički fakultet, Univerzitet u Beogradu)
Abstract
Induction motor drives with conventional field-oriented control maintain the rotor flux at its rated level throughout the constant torque region, which corresponds to holding the stator current d component constant. Since the loss-minimum, or efficiency optimal flux depends on the load, this results in a significant efficiency penalty at light load conditions. This paper presents a neural network-based loss-minimising controller in which the stator current d component reference is generated depending on the operating point rather than held constant.
An analytical loss model is developed to demonstrate that the total loss is a convex function of the d-axis current, with an minimum that shifts toward lower flux in light load conditions. The loss-minimum current mapping is then obtained directly from the drive simulations in Matlab/Simulink by sweeping the d-axis current in a range of interest, at each of selected 25 operating points and measuring the input power at the DC link. Because the measurement is taken at a drive-level basis, the resulting mapping accounts for the efficiency of the system as a whole. A feedforward network with two hidden layers is trained on this data and encodes the mapping in 151 weights and biases, evaluated once per speed-loop sampling period.
Simulation results for a 4 kW drive show efficiency improvements of up to 38% at light load, with speed regulation accuracy unaffected and the stator current magnitude reduced by up to 50%. The improvement diminishes toward rated load, where the efficiency optimum coincides with rated flux and is constrained by the available inverter voltage, confirming that full-load performance is not degraded.
M. Ivanović, B. Gajić, M. Stamenić, S. Genić, M. Otović (Univerzitet u Beogradu – Mašinski fakultet)
Abstract
Procesni visokotemperaturski aparati svrstavaju se u energetski najzahtevnije elemente postrojenja, a karakteriše ih kompleksnost istovremenog odvijanja hemijskih transformacija i faznih prelaza, uz turbulentno strujanje i razmenu toplote. Operateri ovakvih aparata se često suočavaju sa problemima zaprljanja i lokalnog pregrevanja razmenjivačkih površina, što može da izazove njihov nepravilan rad i neplanirane zastoje. Ovakvi operativni problemi često su direktna posledica neravnomerne raspodele toplotnog fluksa i protoka fluida. Konkretno, u inženjersku praksu rafinerijske industrije su većinski implementirane tradicionalne proračunske procedure vezane za ložišta, gde se navedene pojave ne predviđaju u dovoljnoj meri zbog korišćenja osrednjenih vrednosti toplotnog fluksa i zanemarivanja temperaturskih profila gorionika. Merenjima i CFD proračunima potvrđeno je da stvarna vrednost longitudinalnog faktora neravnomernosti toplotnog fluksa može biti i do 40% veća (do FL = 1,7) od standardom API 530 definisane vrednosti prema dimenzijama ložišta i odnosu na širinu i visinu plamena. Pored toga, prisutni su konstantno rastući zahtevi za energetskom efikasnošću, smanjivanjem emisije zagađujućih komponenti i produženjem radnog veka opreme. Smanjenje konzervativizma u projektovanju podrazumeva korišćenje pouzdanih matematičkih modela kako bi se procesni aparat koristio efikasnije, ali imperativ uvek ostaje isti, tj. da se zadovolje bezbednosni zahtevi koji su propisani standardima. Napredniji matematički modeli i korišćenje CFD metode smanjuju nesigurnost u proceni realnih uslova tokom eksploatacije, tako da je omogućeno da se standardi menjaju, ne u smislu njihove relaksacije, već preciziranja zahteva sigurnosnih ograničenja. Prema opštem konsenzusu, uvek je povoljnije sprečiti pojavu problema u inicijalnim fazama, tj. fazi projektovanja, gde su ključni fizički i matematički modeli. Ovaj rad se bavi pregledom, poređenjem i ograničenjima nekih od postojećih matematičkih modela proračuna ložišta kod visokotemperaturskih procesnih aparatа i paralelom razvoja standarda po osnovu usvojenih preporuka za eliminisanje/smanjenje ili prevenciju operativnih problema i povećanja efikasnosti. U radu je data uporedna analiza dva modela strujanja na razmenjenu količinu toplote u ložištu sa prirodnim gasom kao gorivom.
Vladimir Stevanović (Mašinski fakultet Univerziteta u Beogradu)
Abstract
Na savremenim termoelektranama loženim ugljem su primenjena rešenja za iskorišćenje otpadne toplote dimnih gasova između elektrofiltera i postrojenja za odsumporavanje dimnih gasova, koja omogućuju značajno povećanje stepena korisnosti parnih blokova. U tu svrhu su razvijeni i novi materijali koji nisu podložni niskotemperaturskoj koroziji. Navedena rešenja su primenjena i na starijim termoelektranama, rekonstrukcijama na osnovu inoviranih prvobitnih projektnih rešenja. U ovom radu se prikazuju primeri nekih izvedenih rešenja, kao i moguće potencijalne primene u cilju povećanja efikasnosti parnih blokova i predaje toplote sistemu daljinskog grejanja.
Đorđe S. Čantrak (University of Belgrade - Faculty of Mechanical Engineering)
Abstract
Pumps consume approximately 20% of the world’s total electricity [1]. More than 30% of pumps work in an inefficient way [2]. So, there are great opportunities for energy management. Implementation of variable frequency drives, correct equipment sizing, application of optimized running strategies, regular maintenance, could dramatically increase energy savings. Do the pump producers today only rely on these aspects or they invest, also, in hydraulic design improvements? What is a case for small and what about bigger pumps?
In order to better understand pump hydraulic and overall efficiency, in this paper will be discussed fluid flow phenomena in the most frequently used type of pumps – centrifugal [3]. Some aspects of modern pump design will be discussed [4], as well as some machine learning methods for optimizing cavitation performance of a centrifugal pump [5]. In addition, international standard ISO 9906:2012 Rotodynamic pumps - Hydraulic acceptance tests – Grades 1, 2 and 3 [6] and its implementation in the laboratory of the Chair for Hydraulic Machinery and Energy Systems University of Belgrade – Faculty of Mechanical Engineering (Laboratory) will be discussed [7]. Some experimental results obtained in the Laboratory by using modern experimental techniques, such as laser Doppler velocimetry [8] and high speed cameras, as well as classical ones, will be presented.
Adequate strategies of pump design, manufacturing, testing and running are corner stones for energy efficient application of pumps.
This shows a need for a better understanding of the fluid flow phenomena in centrifugal pumps.
Lazar Laković (Univerzitet u Beogradu, Mašinski fakultet, Katedra za računarstvo, Beograd, Srbija)
Abstract
Proizvodnja mikrobilja u kontrolisanom okruženju zahteva održavanje stabilnih mikroklimatskih uslova, precizno navodnjavanje i racionalno korišćenje električne energije i vode. U praksi se ovakvi sistemi često oslanjaju na fiksne vremenske režime rada rasvete, ventilacije i pumpi, što ne uzima uvek u obzir stvarno stanje u proizvodnom prostoru i može dovesti do nepotrebne potrošnje resursa ili neujednačenih uslova uzgoja. Ovaj rad predstavlja pristup razvoju senzorskog sistema za praćenje i upravljanje proizvodnjom mikrobilja u kontrolisanom okruženju, sa posebnim naglaskom na energetsku i resursnu efikasnost. Predloženi sistem obuhvata akviziciju podataka sa senzora temperature i relativne vlažnosti vazduha, osvetljenosti, vlažnosti supstrata, nivoa vode i radnog stanja ključnih izvršnih elemenata, kao što su LED rasveta, pumpe za navodnjavanje i ventilacija. Prikupljeni podaci se obrađuju u softverskoj platformi koja omogućava vizualizaciju parametara, praćenje odstupanja od zadatih vrednosti i formiranje upravljačkih odluka. Upravljanje se zasniva na pravilima i graničnim vrednostima definisanim prema potrebama pojedinačnih proizvodnih ciklusa, čime se omogućava prilagođavanje rada sistema realnim uslovima u prostoru, umesto isključivo fiksnom vremenskom rasporedu. Kao studija slučaja posmatra se proizvodnja mikrobilja na vertikalnim policama, gde su najznačajniji potrošači energije rasveta, ventilacija i oprema za cirkulaciju vode. Cilj rada je da se prikaže arhitektura sistema i metodologija za praćenje potrošnje energije i vode, stabilnosti mikroklimatskih parametara i ponovljivosti proizvodnih ciklusa. Predloženi pristup predstavlja osnovu za dalji razvoj autonomnog upravljačkog sistema koji može doprineti efikasnijem korišćenju resursa i pouzdanijoj proizvodnji mikrobilja u kontrolisanim uslovima.
Valery Halavachou (Howden Turbo GmbH, Frankenthal, Germany)
Alexander Begliak (Howden Turbo GmbH, Frankenthal, Germany)
Abstract
The ongoing energy transition and the increasing share of fluctuating industrial and
energy processes are creating new requirements for steam turbine technology.
Waste-to-Energy plants, waste heat recovery systems, combined heat and power
(CHP) facilities, and industrial steam networks require equipment capable of rapid
start-up, efficient operation under varying load conditions, and high performance
across a broad operating range.
This paper presents the design concept of Howden Turbo KK&K steam turbines,
based on an overhung rotor arrangement, an integrated gearbox, and an integrated
lubrication system. This architecture provides a highly compact turbine package,
simplifies installation and maintenance, and enables cold starts without pre-heating
or shaft turning equipment.
Particular attention is given to the relationship between turbine architecture and
operational performance. Key advantages include rapid load response, high
efficiency at part-load operation, the capability for frequent start-stop cycles, and the
ability to operate with dry saturated steam. The compact arrangement and integrated
gearbox enable an optimized turbine design while minimizing installation footprint
and auxiliary equipment requirements.
Case studies from waste heat recovery, Waste-to-Energy, CHP, and industrial
applications demonstrate that compact overhung steam turbines with integrated
gearbox technology provide an effective solution for facilities where operational
flexibility, high availability, and reduced capital and operating costs are critical factors.